Our Test Chamber range just got bigger!

Fuseco is proud to announce that we have started a partnership with the company Haida International.

Haida International specialises in products for mechanical testing such as Environmental test chambers, IPX test chambers, age testers and shake tables.

With every mechanical part manufactured in house, expect a quick turnaround for both new orders and spare parts.

If there is any test requirement that is not covered by their large range of standard units, they are happy to design and manufacture custom solutions to meet your specifications.

Temperature Humidity Environmental Test Chamber

A temperature and humidity test chamber provides a wide temperature and humidity control range. It is utilised to simulate high temperature, low temperature or damp heat environment. Customers can select models based on performance and test area capacity.


  • High performance and quiet operation (68 dBA)
  • Space-saver which is designed for flush installation to wall
  • Full thermal break around doorframe
  • One 50mm diameter cable, with a flexible silicone plug
  • Direct water supply connection for continuous operation
  • Accurate wet/dry-bulb humidity measurement system, which makes it easy to maintain



Rapid-Rate Thermal Cycle Chamber Equipment

This chamber is ideally suited for specimen test requiring quick changes of temperature. It can evaluate the failure of thermal mechanical properties of a product. Normally the temperature rate is less than 20C/min, which can achieve the real application environment of testing sample by the fast ramp rate.


  • Has cable ports which are provided on the left side to allow easy wiring of specimens for measurement or voltage application
  • The door is equipped with hinges which prevents automatic closure
  • Designed to comply with major environmental test standards like IEC, JEDEC, SAE...
  • This chamber is safety tested with CE certificate



Double-Battery Explosion-Proof Test Chamber

This tester is mainly used for battery overcharge and overdischarge, charge and discharge test. The battery is placed in the explosion-proof box, external charge and discharge tester, for the protection of the operator and the instrument. The test box of this machine can be customised according to the test requirements.


  • Operates in 25±5℃ (Room Temperature)
  • 1 test hole of 50mm diameter on the right side of the device
  • Thermal shock test for battery products
  • Weighs approximately 65kg



Salt Spray Chamber

Haida's Salt Spray Chamber is the standard product used to detect salt spray corrosion resistance of the material or material surface coating. This chamber is equipped with an intelligent salt spray test system that enables quick and standardised conversion of test modules.


  • Provides USB Host for USB flash drive
  • Touch-screen operator control interface
  • ‘Easy Open’ canopy
  • Dry seal gasket prevents wetting operator’s clothes, etc
  • Low loading threshold for loading and unloading
  • Large capacity floor standing salt solution reservoir
  • Calibration certificate
  • Canopy color choice
  • Set of sample racks



UV Accelerated Test Chamber

The UV Accelerated Test Chamber can simulate the hazards caused by sunlight, rain and dew. This product is designed to get the results of damage after several days or weeks which is equal to exposure to the outworld world for a few months.


  • Programmable controller
  • LCD touch screen
  • Built-in protection system



Vibration Shaker Testing Equipment

Vibration Shaker Testing Equipment is widely used in defense, aviation, aerospace, communications, electronics, automobiles, home appliances and other industries.


  • Sine wave, FM, sweep, programmable
  • Frequency multiplier, logarithm
  • Maximum acceleration
  • Amplitude modulation
  • Time control
  • Full function computer control
  • Simple fixed acceleration/fixed amplitude
  • Stable performance
  • Reliable quality



Fuseco are the leading experts in Test Equipment across Australia. We are partners with some of the world’s leading suppliers in Test Equipment which allows us to provide our clients with the highest-quality products. We can be active participants in those crucial early concept phase discussions regarding the various solutions available.

Please contact the team at FUSECO for further information and completive pricing for all your Test Equipment Requirements.

We're here to help

Talk to an expert today.
Our friendly team of highly trained specialists will quickly assist you.

Get a quote technical support 1300 387 326

We promise to respond within 4 business hours (AEST).

Or you will receive $100 off your next purchase. Read how it works.

Our Experience

We offer you advice that is gained from many years of assisting people from all industries with their individual requirements, technical objectives and challenges.

most advanced solutions

The Ametek stable of brands the are industry's greatest innovators, always being the first to release new technologies & features.  

Satisfaction guarantee

We work hard to ensure that you are very happy with every aspect your new test equipment solution and provide the most attentive after-sales care in the industry.

Top FAQs

Electrostatic discharge (ESD) is the sudden flow of electricity between two electrically charged objects caused by contact, an electrical short, or dielectric breakdown. A buildup of static electricity can be caused by turbocharging or by electrostatic induction.

Simulates electrostatic discharge events directly to the product, or to a nearby conductive surface.

Test Method

The ESD test requires that discharges be made to all exposed surfaces of the EUT, including connector back shells. Contact discharge is to the conducting surfaces of the product and air gap discharges are to non-conducting surfaces. The test also requires that contact discharges be made to a horizontal reference plane and vertical reference plane at locations 10cm from the front, rear and sides of the EUT. The ESD Simulators/Generators/Guns can be used for ESD Testing.

Typical rise time of the ESD pulse waveform is approximately 0.7 - 1nS with a hold time of 30 - 60 nS. (See image)


The test simulates ESD events that occur when the user touches the equipment under test or nearby metallic objects (e.g. filing cabinets). The test levels for both the heavy industrial and light industrial/commercial/residential standards are ±2kV and ±4kV for the contact discharge method and ±2kV, ±4kV, and ±8kV for the air gap discharge method.

A transient event is a short-lived burst of energy in a system caused by a sudden change of state. The source of the transient energy may be an internal event or a nearby event. The energy then couples to other parts of the system, typically appearing as a short burst of oscillation.

In electrical and electronic engineering such electromagnetic pulses (EMP) occur internally as the result of the operation of switching devices. Engineers use voltage regulators and surge protectors to prevent transients in electricity from affecting delicate equipment. External sources include lightning (LEMP), electrostatic discharge (ESD) and nuclear EMP (NEMP).

Within Electromagnetic compatibility testing, transients are deliberately administered to electronic equipment for testing their performance and resilience to transient interference. Many such tests administer the induced fast transient oscillation directly, in the form of a damped sine wave, rather than attempt to reproduce the original source. International standards define the magnitude and methods used to apply them.

Simulates high frequency electrical disturbance on power and signal lines due to the switching of inductive loads on the AC line.

Test Method

The test waveform consists of a 15ms burst of pulses at 300ms intervals. The pulses have a rise time of 5ns and a dwell time of 50ns, with a repetition rate of 5 kHz.

For heavy industrial equipment the test levels are:

  • AC lines; ±2kV
  • DC lines;
  • ±2kV Signal lines on cables that could be longer than 3m; ±1kV
  • Process control lines and measurement lines; ±2kV

Noise is directly injected onto power lines through a capacitor and capacitive coupled onto I/O lines using a coupling trench. DC power ports connected to an AC-DC power adapter are not tested.

Surges, or transients, are brief overvoltage spikes or disturbances on a power waveform that can damage, degrade, or destroy electronic equipment within any home, commercial building, industrial, or manufacturing facility. Transients can reach amplitudes of tens of thousands of volts.

Simulates low frequency, high-energy electrical transients on power lines and long distance I/O lines (such as telephone lines) coupled from nearby lightning strikes.

Test Method

Test is applied to AC and DC power ports. The open circuit signal wave-shape has as 1.2µs rise time and 50µs hold time. Surges are applied in common mode (line-to-ground) and in differential mode (line-to-line). All surges are synchronized to the 0°, 90°, 180° and 270° phase angles of the AC voltage. DC power ports are not tested if they are connected to an AC-DC power adapter, in which case the AC-DC adapter should be submitted for testing.

Test levels for the residential, commercial and light industrial generic standard are 2kV common mode and 1kV differential mode on AC power lines. For DC power lines, the test levels are 0.5kV for both differential and common mode. Although the test is not currently required for the heavy industrial generic standard, it suggests test levels of 4kV common mode and 2kV differential mode.

Simulates brown outs and blackouts on AC power lines.

Test Method

This test is applied to AC power ports rated at less than 16 amps per phase. All voltage shifts are synchronized to the zero crossing of the AC voltage.

Typical test levels for the generic light industrial standard involve a 30 percent dip in the line voltage for 10ms, 60 percent dip for 100ms and dropout for 5000ms. There are currently no requirements for Heavy Industrial equipment.

All linear amplifier systems, when given a sufficiently strong input signal, will reach a point where the system departs from a linear relationship between input and output. At this point the system is said to be going into compression or beginning to saturate. Beyond this point, the linear relationship between input and output is no longer valid and the amplifier is no longer considered to be linear. An internationally recognised figure of merit, used for defining the extent of linearity of an amplifier, is the 1dB compression point. This is the point of –1dB departure from linearity. The output power of an amplifier cannot increase indefinitely and when an increase in input power generates no discernible increase in output power, the amplifier is said to be saturated, and by definition the output is not proportional to the input signal. This point is often referred to as Psat on a datasheet or sometimes P3dB. Generally, saturated power is of importance when considering the pulsed power requirements in something like automotive testing while linear power is of importance when considering the AM (amplitude modulation) waveform used in commercial EMC testing.

Applicable Industries

Thank you for helping our team select the correct product to facilitate testing to the various required standards. Our lab is now equipped with a range of Teseq, IFI and Milmega products and the entire solution fulfils our testing requirements. We really appreciate your technical advice & support.

Scott Emerson


Aside from receiving information when we need to upgrade or purchase an item of test equipment, what we really need from an equipment partner is advice based on industry experience. Thank you for the many hours spent talking to us and answering our questions. This level of customer care is rare in this industry.

Janet Boyle


The Teseq GTEM is a great testing tool to have. We are now performing all pre-compliance testing in-house and saving lots of money which we were spending earlier with test labs. It has given us significant more testing capability and flexibility. Thank you for your help.

Sue Benton


Technical Support

Our experts are all pre-eminent leaders in electrical products who provide excellent support in their areas of expertise.

Technical support

Talk to an expert

Our friendly team are highly trained product experts who really enjoy helping customers find what they need.

1300 387 326

call 1300 387 326

Enquire by email

We promise to respond within 4 business hours (AEST) or you will receive $100 off your next purchase.

Enquire now