200kVAr Wall Mounted PFC Solution!

200kVAr Wall Mounted PFC Solution!

We are excited to announce the release of the new Sinexcel 200kVAr Static Var Generator (SVG) module! Available in Wall-mount or Rack-mount options, the new 200kVAr module provides the best ‘size to kVAr’ ratio available in the market. Easily incorporated into any switch room, the Sinexcel SVG is designed to meet the fast switching, high harmonic content, non-linear loads of today’s electrical environments.

Unprecedented performance!

  • Maintains PF 0.99
  • Dynamic instantaneous step-less compensation
  • No switched AC capacitor banks
  • Can be connected in parallel for even greater capability
  • 200kVAr in a single wall-mount Module
  • 600kVAr in a single cabinet
  • Virtually no on-going maintenance costs
  • Load balancing
  • Corrects lagging (inductive loads) AND leading (capacitive loads)
SVG 200kVAr_Waveform Copy

Sinexcel SVG in Action

This screen shot is from a Sinexcel SVG unit operating at one of our customer locations.

Corrects PF to 0.995

The PF on this site ranges from 0.842-0.858 lagging across the three phases, which is considered poor and correction is required.

The Grid Current information at the top left of the screen displays the corrected RMS Current and PF after compensation by the Sinexcel SVG. Note, the PF has been corrected to 0.995 lagging.

Corrects Load Balance

Secondly, this site has a significant phase current imbalance. The RMS between the 3 phases ranges from 816A to 858.9A. That is a 42.9A phase current imbalance.

From the Grid Current information at the top left of the screen, we can see that the phase current imbalance has been corrected and the RMS has been reduced to 442A (approx. 17% reduction).

This sort of performance cannot be achieved with traditional PFC systems.

SVG does not use AC capacitor banks so it does not have the reliability issues & ongoing costs associated with these. 
At just 48kg, the 100kVAr Sinexcel SVG wall mounted unit is the most compact power factor correction solution in the world.
By balancing the load across all three phases, the SVG reduces the peak current which in turn reduces the peak demand tariff (electricity bills) and the load on the switchboard.
The SVG provides compensation instantaneously in real-time to each phase individually with no possibility of over-compensation or under-compensation.

The Sinexcel SVG Product Range

Wall-Mount Solutions


100kVAr (Pro Series)


Rack-Mount Solutions


100kVAr (PRO Series)



Up to 500kVAr
Standard Flexi-Cabinet
800W x 800D x 2200H (mm)

Up to 600kVAr
Large Flexi-Cabinet
800W x 1000D x 2200H (mm)

How can Fuseco help you?

Fuseco is Australia's leading experts in Power Factor Correction. Contact us for a free site appraisal and no obligation assessment to see if you can save money on your energy costs.

We welcome you to contact us and tell us about your site. We will happily assess your bill and determine whether you need Power Factor Correction.

If you do, we will offer a tailored solution and show you how much you will save. We will also clearly explain your Return On Investment (ROI) so you can make an informed decision.

There’s no charge - no obligation.

 Reducing your electricity costs with Power Factor Correction

 Learn more about Power Factor 

Check out the Sinexcel SVG Product Range

We're here to help

Talk to an expert today.
Our friendly team of highly trained specialists will quickly assist you.

Get a quote technical support 1300 387 326

We promise to respond within 4 business hours (AEST).

Or you will receive $100 off your next purchase. Read how it works.

Top FAQs


27 Viking Court

Cheltenham VIC 3192


29/8-10 Barry Road

Chipping Norton NSW 2170


1 / 26 Duke Street

Sunshine Beach QLD 4567


67 Howe Street

Osborne Park WA 6017

We'd love to hear from you! At Fuseco, rather than publish generic prices, we prefer to give you an individual quote. This ensures that we provide you with the best possible pricing to meet your needs.

The quickest way to place an order is to give our customer service team a call or send us an email. We promise to respond within 4 hours or you get $100 off your next order, however we usually respond within 1-2 hours to email enquiries. So go ahead and speak to us, we'd love to help you with your needs.

Fuse Products

  • For all orders over $100 (excl. GST & freight), freight is FIS (Free into Store).
  • For all orders under $100 (excl. GST & freight), a freight charge of $25 + GST is applicable.
  • Additional fees may apply for deliveries to the Northern Territory and remote areas.

All Other Products

  • Freight charges POA (Price on Application)
  • FOT (Customer nominates own carrier and accepts all charges)

Freight details

In simple terms, harmonics are extra frequencies that when present in an electrical circuit, distort the AC sine wave. A harmonic of a wave is a component frequency of the signal that is an integer multiple of the fundamental frequency. For example, if the fundamental frequency is f, the harmonics have frequencies 2f, 3f, 4f... etc. 

Harmonic frequencies are equally spaced by the width of the fundamental frequency and can be found by repeatedly adding that frequency. In the case of the Australian electricity supply, the fundamental frequency is 50Hz. The frequencies of the harmonics are 100Hz, 150Hz, 200Hz, 250Hz, 300Hz, 350Hz and so on.

Learn more

For electrical systems to function in their intended manner without significant loss of performance or life, they require a supply of electricity that is of good quality. Good quality electrical power has the following characteristics: 

  • It must have a continuity of service (not be interrupted). 
  • It must have a very low Harmonic content. 
  • It must have a very low variation in the voltage magnitude. 
  • It must have very low transient voltages and currents. 

The term 'clean power' is used to describe electricity that is considered to be of good quality (see above) with particular reference to a very low harmonic content. Therefore, the term 'dirty power' is used to describe electricity that is considered to be of low quality (opposite to the above) with particular reference to a very high harmonic content. 

In Australia, our electricity is supplied in alternating current at a frequency of 50Hz. In alternating current (AC) the movement of electric charge periodically reverses direction. In direct current (DC), the flow of electric charge is only in one direction. 50Hz means that the AC has a frequency of 50 cycles per second. This is also known as the 'fundamental' frequency. AC is the form in which electricity is delivered to businesses and residences. Most electrical devices (such as motors) need clean electricity to function properly. This means that the electrical supply needs to be a clear sinusoidal wave.

Learn More

If you occasionally experience some unexplained occurrences such as flickering lights, alarms going off, or MCB's, MCCB's, RCD's and Earth Leakage devices tripping for no apparent reason, you are most likely experiencing harmonics in your electrical environment. Other signs are cables running hot, hot switchboards or overheating motors. If you are replacing your motor's bearings & insulation often, that's a strong indication of the presence of harmonics.

Learn more

Harmonics are very harmful within an electrical system and can have serious consequences. For example, the presence of harmonics reduces the life of equipment. It is possible that the investment that you made in your motors & drives will not be realised if they are damaged and need replacing before their expected life span. This can be very expensive. Harmonics cause things to run hot, which cause stress on the cables and equipment.

In the long term, this degrades an electrical system. The presence of harmonics will also mean that although you will get billed for the power that you are supplied, a large percentage of that power may be unusable. Harmonic mitigation is taking action to minimise the presence of harmonics in your electrical system and can achieve great cost savings.

Variable Speed Drives (also known as Variable Frequency Drives) are prolific creators of harmonics in electrical systems and as a result, most of the harmonic mitigation effort focuses on the input side and output side of a VFD.

Learn more

Depending on the specific situation, there are a variety of products that are used to mitigate harmonics. Fuseco's Power Quality Consultants can assist by conducting a site analysis or simply providing advice based on the details of the particular electrical system. Here is a brief summary of the product groups:

Line (input) side of the VSD

Device Features:

  • Line Reactors Simple & cost-effective method to reduce harmonics. Available in 3% & 5% versions.
  • Passive Harmonic Filters Significantly reduces harmonics from the VSD back out to the system and also improves true power factor.
  • Meets the IEEE519 Standard.
  • Active Harmonic Filters Active filters inject a 180 degree inverse current to nullify the harmonic content going back out to the system. They mitigate harmonics, compensate for voltage dips & can handle multiple VSD's relative to the reactive power required. Meets the IEEE519 Standard.

Load (output) side of the VSD

Device Features:

  • Load Reactors Simple & cost-effective method to reduce harmonics. Available in 3% & 5% versions.
  • dV/dT Filters dV/dT filters have been designed to limit peak voltage and increase voltage rise time. In addition to mitigating harmonics, the dV/dT filter also clips voltage spikes.
  • Sinewave Filters The ultimate load side harmonic mitigation product. Filters all harmonics, including reflective currents, eddy currents, common mode currents. Can be used for long cable runs (many kms). Stops the heating of cables. Great for the longevity of motors.

From the moment the AHF and SVG units were turned on our power factor issues were a thing of the past. At both sites our PF is now 0.99 on all phases all the time, the units react instantaneously to our fluctuating load and power factor and the result has been an excellent return on investment.

Brad Kilner


Technical Support

Our experts are all pre-eminent leaders in electrical products who provide excellent support in their areas of expertise.

Technical support

Talk to an expert

Our friendly team are highly trained product experts who really enjoy helping customers find what they need.

1300 387 326

call 1300 387 326

Enquire by email

We promise to respond within 4 business hours (AEST) or you will receive $100 off your next purchase.

Enquire now